1. Кіріспе
The Hantek DSO5000P series digital storage oscilloscopes (DSO) are versatile and high-performance instruments designed for various electronic measurement tasks. This series includes models DSO5072P, DSO5102P, and DSO5202P, offering bandwidths of 70MHz, 100MHz, and 200MHz respectively, with a 1GSa/s real-time sample rate. These oscilloscopes feature a large 7.0-inch color display (WVGA 800x480) and a record length of up to 40K, making them suitable for detailed signal analysis in educational, industrial, and research environments.
This manual provides essential information for the safe and efficient operation, setup, and maintenance of your Hantek DSO5000P series oscilloscope.
2. Негізгі мүмкіндіктер
- Bandwidths: 70MHz (DSO5072P), 100MHz (DSO5102P), 200MHz (DSO5202P)
- 1GSa/s Real-Time Sample Rate
- Large 7.0-inch WVGA (800x480) Color Display
- Record Length up to 40K points
- Multiple Automatic Measurements
- Trigger Modes: Edge, Pulse Width, Line Selectable Video, Slope, Overtime
- USB Host and Device Connectivity for PC Analysis
- Four Math Functions, including FFT
3. Қауіпсіздік туралы ақпарат
Always observe the following safety precautions to prevent injury and avoid damage to the instrument or connected devices.
- Қуат көзі: Тек көрсетілген қуат адаптерін және томды пайдаланыңызtage. Ensure the power cord is properly grounded.
- Қоршаған орта: Operate the oscilloscope in a dry, well-ventilated area, away from direct sunlight, dust, and corrosive gases. Avoid extreme temperatures.
- Зондтар: Use only probes rated for the voltage and current being measured. Ensure probes are properly connected before applying power.
- Желдету: Do not block the ventilation openings on the instrument.
- Қызмет көрсету: Refer all servicing to qualified service personnel. Do not attempt to open or repair the instrument yourself.
4. Пакет мазмұны
Пакетте келесі элементтер бар екенін тексеріңіз:
- Hantek DSO5000P Series Digital Storage Oscilloscope
- Two Passive Probes (1X/10X switchable)
- Қуат сымы
- USB кабелі
- CD-ROM with PC Software and User Manual
- Жылдам нұсқаулық
5. Орнату
Follow these steps to set up your oscilloscope for initial use.
5.1 Физикалық аяқталуview
Familiarize yourself with the front, rear, and side panels of the oscilloscope.
This image displays the front, rear, and side views of the Hantek DSO5102P oscilloscope, highlighting its physical layout and connection ports.
5.2 Қуат қосылымы
- Connect the power cord to the AC input on the rear panel of the oscilloscope.
- Қуат сымының екінші ұшын жерге қосылған айнымалы ток розеткасына қосыңыз.
5.3 Probe Connection and Compensation
- Connect a passive probe to one of the input channels (CH1 or CH2) on the front panel.
- Attach the probe ground clip to the ground terminal on the oscilloscope.
- Set the probe attenuation switch (if applicable) to 10X.
- Connect the probe tip to the probe compensation output terminal (usually a square wave signal).
- Power on the oscilloscope by pressing the power button.
- Adjust the probe compensation trimmer on the probe until the square wave displayed on the screen has flat tops and bottoms, without overshoot or undershoot.
This image shows the Hantek DSO5102P oscilloscope actively measuring signals on a circuit board using a connected probe.
6. Пайдалану нұсқаулары
This section covers basic operation of the DSO5000P series oscilloscopes.
6.1 Алдыңғы панельді басқару элементтері
The front panel is organized into several functional areas:
- Vertical Controls: Көлемді реттеуtage per division (Volts/Div) and position for each channel.
- Horizontal Controls: Adjust time per division (Sec/Div) and horizontal position.
- Триггерді басқару элементтері: Set trigger level, mode, and type to stabilize waveforms.
- Функция түймелері (F1-F6): Context-sensitive buttons for menu navigation and selections.
- Measurement Buttons: Access automatic measurement functions.
- Utility Buttons: Save/Recall, Acquire, Display, Cursor, Math, etc.
This image provides a detailed front view of the Hantek DSO5102P oscilloscope, illustrating the layout of its display, control knobs, and function buttons.
6.2 Basic Waveform Display
- Connect a signal source to CH1.
- түймесін басыңыз АВТООРНАТУ button for automatic waveform display optimization.
- реттеңіз ТІК ОРН және VOLTS/DIV knobs to fine-tune the vertical scale and position of the waveform.
- реттеңіз Горизонтальды позиция және SEC/DIV knobs to fine-tune the horizontal scale and position.
- реттеңіз TRIGGER LEVEL knob to stabilize the waveform.
This image displays several examples of waveforms captured and analyzed on the oscilloscope screen, demonstrating its measurement capabilities.
This image presents a grid of six different oscilloscope screen captures, illustrating the device's ability to display and analyze various signal types simultaneously.
6.3 Using Automatic Measurements
түймесін басыңыз ӨЛШЕУ button to access the automatic measurement menu. Use the function buttons (F1-F6) to select desired measurements such as Vpp, Vmax, Vmin, Frequency, Period, Rise Time, Fall Time, etc. The results will be displayed on the screen.
6.4 PC Connectivity
Connect the oscilloscope to a computer using the provided USB cable. Install the PC software from the included CD-ROM. This software allows for real-time data analysis, waveform storage, and remote control of the oscilloscope from your computer.
7. Техникалық қызмет көрсету
7.1 Тазалау
Құралды тазалау үшін жұмсақ шүберекті пайдаланыңызampened with mild detergent and water. Do not use abrasive cleaners or solvents that may damage the casing or screen. Ensure the instrument is powered off and disconnected from all power sources before cleaning.
7.2 Сақтау
When not in use, store the oscilloscope in a clean, dry environment, away from extreme temperatures and humidity. Protect the screen from scratches and impacts.
8. Ақаулықтарды жою
Егер сіз осциллографпен мәселелерге тап болсаңыз, келесі жиі кездесетін мәселелер мен шешімдерді қараңыз:
- Дисплей жоқ: Ensure the power cord is securely connected and the power button is pressed. Check the brightness settings.
- No Waveform: Verify that probes are correctly connected to the input channels and the signal source. Check probe compensation and attenuation settings. Use the AUTOSET function.
- Тұрақсыз толқын формасы: Adjust the trigger level and trigger mode. Ensure the trigger source is correctly selected.
- Incorrect Measurements: Check probe attenuation settings (1X/10X) and ensure they match the oscilloscope's channel settings. Perform probe compensation.
- PC Software Connection Issues: Ensure the USB cable is properly connected and the correct drivers are installed on your PC. Restart both the oscilloscope and the PC.
For persistent issues, contact Hantek customer support.
9. Техникалық сипаттамалар
Detailed technical specifications for the Hantek DSO5000P series oscilloscopes.
This image presents a comprehensive table detailing the technical specifications for the DSO5072P, DSO5102P, and DSO5202P models.
| Параметр | Мән |
|---|---|
| Өндіруші | Хантек |
| Бөлшек нөмірі | Q-DSO5202P |
| Элемент салмағы | 3 келі |
| Өнім өлшемдері | 10 x 31.5 x 14 см; 3 кг |
| Өндіруші тоқтатқан | Жоқ |
| Size (Model) | DSO5202P |
| Түс | Түрлі түсті |
| Стиль | Bench Oscilloscope |
| Материал | Акрилонитрилді бутадиен стиролы |
| Ватtage | 1 Вт |
| Өлшеу жүйесі | Метрика |
| Өлшеу дәлдігі | 0.3% |
| Сертификаттар | CE, ISO 9001, RoHS |
| Қосылған құрамдас бөліктер | DSO5202P (main unit, probes, power cord, USB cable, software CD) |
| Элемент өлшемдері (LxWxH) | 10 x 31.5 x 14 см |
| ASIN | B0C72HY47Z |
| Бірінші күні Amazon.co.jp сайтында қолжетімді | 2023/6/4 |
| Параметр | DSO5202P | DSO5102P | DSO5072P |
|---|---|---|---|
| Өткізу қабілеті | 200 МГц | 100 МГц | 70 МГц |
| Sample Rate (Real-Time) | 1ГСа/с | ||
| Equivalent Sample Rate | 25ГС / с | ||
| Қабылдау режимдері | Normal, Peak Detect, Average (4, 8, 16, 32, 64, 128) | ||
| Жазба ұзындығы | 40 мың | ||
| Inputs Coupling | AC, DC, GND | ||
| Кіріс кедергісі | 1MΩ ±2% || 20pF ±3pF | ||
| Зондтың әлсіреуі | 1X, 10X, 100X, 1000X | ||
| Максималды кіріс көлеміtage | CAT I and CAT II: 300VRMS (10×), Installation Category II: derate at 20dB/decade above 100kHz to 13V peak AC at 3MHz*. For non-sinusoidal waveforms, peak value must be less than 450V. Excursion above 300V should be of less than 100ms duration. RMS signal level including all DC components removed through AC coupling must be limited to 300V. If these values are exceeded, damage to the oscilloscope may occur. | ||
| Көлденең SampБағалау диапазоны | 500MS/s – 1GS/s | ||
| Толқын пішінінің интерполяциясы | (sin x)/x | ||
| SEC/DIV Range | 2ns/div to 80us/div | ||
| Sample Rate and Delay Time Accuracy | ±50ppm (at over any ≥1ms time interval) | ||
| Офсеттік диапазон | 2ns/div to 8ns/div: 20ns/div to 80us/div: (-8div x s/div) to 40ms; 200us/div to 80s/div: (-8div x s/div) to 400s | ||
| Delta Time Measurement Accuracy (Full Bandwidth) | Single-shot, Normal mode: ± (1 sample interval + 100ppm × reading + 0.6ns); >16 averages: ± (1 sample interval + 100ppm × reading + 0.4ns); Sample interval = s/div ÷ 200 | ||
| Тік ажыратымдылық | 8-bit resolution, all channel sampled simultaneously | ||
| Позиция диапазоны | 2mV/div to 20V/div: ±400mV; 50mV/div to 20V/div: ±2V; 500mV/div to 2V/div: ±40V; 5V/div to 10V/div: ±250V | ||
| Rise Time at BNC (typical) | 1.8 ns | 3.5 ns | 5 ns |
| Математикалық функциялар | +, -, ×, ÷, FFT | ||
| FFT Windows | Hanning, Flatop, Rectangular, Bartlett, Blackman; 1024 sampнүкте | ||
| Өткізу қабілетінің шегі | 20 МГц | ||
| Low Frequency Response (-3dB) | ≤10Hz at BNC | ||
| DC Gain дәлдігі | ±3% for Normal or Average acquisition mode, 10V/div to 10mV/div; ±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div | ||
| DC Measurement Accuracy | When vertical displacement is zero, and N ≥16: ± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is selected. | ||
10. Кепілдік және қолдау
Hantek products are designed for reliability and performance. This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty card included in your package for specific terms and conditions.
For technical support, troubleshooting assistance, or warranty claims, please contact Hantek customer service through their official website or the contact information provided with your product. When contacting support, please have your product model number and purchase date available.